15 best putties

When conducting modern spackling work using special materials. The market offers a huge selection of dry mixes and ready-to-use solutions. There are cement, epoxy, latex, polyester and other putties designed for application to various substrates.

Our review presents the best mixes from various manufacturers. For the convenience of the reader, the product rating was divided into finishing, starting and universal blends. Estimated position is based on the characteristics of the product and the opinion of professional builders who have experience with this material.

The best starting putties

A distinctive feature of the starting putty is an affordable price. There are different types of compositions, some can be used only inside buildings, and others - in the most difficult atmospheric conditions.

5 GLIMS Styro Prime

Starting putty GLIMS Styro Prime is specially designed for leveling and strengthening the surface before applying a decorative coating. This elastic mixture forms the strongest layer that prevents moisture ingress, destruction or cracking. The presented product has the best performance and high resistance to water, steam and the lowest temperatures, down to -50 ° C. Thanks to this, GLIMS Styro Prime has a wide range of applications. With its help, you can putty insulation, swimming pool, walls, facade, etc.

The recommended cooking proportions require 330 ml of water per 1 kg of the mixture. With a coating thickness of 2 mm, the consumption of GLIMS Styro Prime will be 3 kg per 1 m². The putty is very easy to use, demonstrates better adhesion to the base and easy distribution with a spatula. Among other things, this building mixture meets all environmental standards and is safe for residential premises.

4 Bergauf glatte zement

Bergauf Glatte Zement base putty will be the best choice if necessary to carry out rough preparation of walls and ceilings before the next stage of repair work. This mortar, which is based on cement, has good ductility and increased resistance to cracking. The use of this putty is justified both indoors and in the facade decoration of buildings, since it is intended for objects with normal and elevated levels of moisture. In addition, the presented solution is designed for operation in a wide temperature range from -50 ° C to 70 ° C.

Bergauf Glatte Zement starting putty is intended only for manual application, with a maximum allowable layer thickness of 0.5 to 15 mm. Suitable for almost any surface, which is planned to apply decorative plaster, wallpaper, finishing putty or paint.To obtain the correct consistency, this mixture must be diluted with 8.2-9.2 l of water, the temperature of which should be in the range of 5 to 25 ° C. At the same time, the approximate consumption of putty is 1 kg per square meter.

3 Volma Standard

Volma Standard putty Standard is widely used in construction. The material is used in the alignment of walls and ceilings in dry rooms. Putty recommended concrete and gypsum-based base. After applying a layer of putty, you can start painting, wallpapering or decorating the surface. Mix is ​​prepared on the basis of knitting gypsum and mineral additives. The composition has high adhesion and resistance to cracking. The advantages of the product should include the presence of insulating qualities, manufacturability.

Experienced craftsmen and novice finishers emit several positive properties of Volma Standard starting putty. It is universality, ease of preparation and application, plasticity, ease of grinding. Of the minuses, consumers note the speed of setting and the lack of color marking.

2 Will base Ecsilk

The best domestic starting putty is a mixture of Foundations Ecsilk. It is intended for leveling walls and ceilings, for eliminating cracks and sealing joints in drywall constructions. The basis of the putty is high-quality white plaster. Special chemical components are added to it. They give the putty plasticity, non-shrinkage, good adhesion. In addition, the material has a low consumption (0.8 ... 0.9 kg / sq. M) with a layer thickness of 1 mm. It is possible to putty the bases from a brick, concrete, gas blocks. After drying, a durable coating with high ductility is formed. The composition is easy to prepare, quickly applied with a spatula, well smoothed.

Domestic builders note the good quality of the starting putty Founded Econsilk, availability, low material consumption. Of the shortcomings, experts distinguish the appearance of cracks after complete drying.

1 Rusean TT

Dry mortar Rusean TT is used as a basic putty and ensures a perfectly flat surface due to its excellent ductility. Since it has the best qualities of moisture resistance, vapor permeability and adhesion, it can be used both for facade works and indoors. It is perfect for basement, bathrooms, porches, etc. This putty can be used to prepare walls and ceilings for applying paint or wallpaper, as well as for embedding cracks and electrical wiring. The presented mixture can be stacked in several layers after the previous one is completely dry, and the thickness of each layer should not exceed 5 mm.

For the best result of performing repair work with the Rusean TT start putty, it is necessary to strictly adhere to the manufacturer's recommendations regarding the proportions and time of mixing. If you putty walls with a solution of thickness of 1 mm, then the estimated consumption of the solution will be 1.1 kg per square meter.

Top Finishing Fillers

When painting walls and ceilings, the smallest defects of the base are clearly visible. Thanks to the finishing putty, it is possible to perfectly prepare the surface for painting or sticking wallpaper.

5 KNAUF Multi-Finish

KNAUF Multi-Finish Putty uses gypsum as a base component, in which polymer components and reinforcing fiber are added to obtain high material performance. This solution makes the mixture the best choice for the perfect treatment of various surfaces before applying paint or pasting wallpaper. Since the presented mixture is distinguished by better plasticity, it is very convenient in application and guarantees a smooth and smooth surface without transitions.KNAUF Multi-Finish putty can be used for sealing gaps and joints of structures, with a maximum layer thickness of not more than 5 mm. It can also be used for continuous leveling up to 3 mm, both for raw uneven surfaces, as well as for finished plasterboard structures or concrete slabs.

KnAUF Multi-Finish Putty for best drying speed. Depending on the layer thickness, as well as the ambient temperature and ventilation, this process takes from 1 to 3 days. At observance of all requirements for surface preparation and proportions of dilution of a dry mix, the best result is guaranteed.

4 Ceresit CT 225

Ceresit CT 225 cement cement putty can eliminate minor errors on the ceiling and walls inside buildings, as well as for work on the facade of buildings. At the same time, it will be effective for hiding cracks, chips and other irregularities on the treated surface, the depth of which does not exceed 3 mm. This putty has the best adhesion against virtually all mineral bases, which ensures the creation of a high-quality and reliable layer.

For the strength and durability of the coating meet the reinforcing fibers, which are included in the dry mix. Of great importance is the method of preparation of Ceresit CT 225 to work. The required amount of water must fully comply with the requirements of the manufacturer. You should also maintain time intervals when mixing, as indicated in the instructions. If you follow all the recommendations putty walls or ceiling with this mixture will be much easier than solutions from other manufacturers.

3 Miners finishing

At the most affordable price, you can purchase a finish putty domestic manufacturers Prospectors. Despite the budget material is of high quality. This was achieved by introducing modifying additives into the gypsum base. Putty is recommended to use for the preparation of ceilings and walls in interior spaces, including those with a high level of humidity. You can putty different types of bases, for example, plastered surfaces, concrete, brick. After complete drying (24 hours), a layer of paint can be applied to the surface or wallpapering can be applied. It is not allowed to trim surfaces that come into contact with food and drinking water.

Consumers consider the best qualities of putty Finishers low cost, plasticity, non-shrinkage, fast hardening. The disadvantages of the mixture is poor mixing and low strength of the dried layer.

2 Weber LR +

Weber LR + finishing putty is used to prepare the surface for decorative processing. It is produced as a dry mix. The working solution is prepared by mixing the construction powder with water. During one operation it is allowed to apply a layer of 1-5 mm thickness. The prepared solution retains its working properties for 48 hours. The material is characterized by high plasticity due to the introduction into the composition of binding components of organic origin. Putty can be applied both manually and mechanically. Mix is ​​intended for preparation of the bases in the heated rooms under painting or under wall-paper.

Russian finishers note the advantages of putty, such as the rapid mixing of layers, simple sanding and getting a perfectly white smooth layer. Unfortunately, not everywhere you can buy this finishing material, and its price is quite high.

1 Sheetrock superfinish

Sheetrock SuperFinish putty ready for use has unique qualities. The manufacturer has mixed all the components in an optimal combination, so before work, the dresser simply needs to mix the working solution and proceed to the application. It was possible to achieve special properties by adding vinyl compounds to the composition.The applied layer dries out within 5 hours. It is recommended to perform further operations after 24 hours. The material has a low shrinkage, which has a positive effect on the quality of the finish. It is convenient to putty putty, it possesses ideal adhesion. The thickness of one layer should be about 2 mm. You can apply paint or glue wallpaper on the putty surface.

Finishing craftsmen call Sheetrock SuperFinish finishing putty the best composition for perfect surface preparation for painting or wallpaper. The only disadvantage of the mixture is the high price.

The best universal putty

In some cases, leveling ceilings, walls and facades is more convenient and more profitable with the help of universal putty. Individual species are suitable for leveling a wide range of materials.

5 Litokol litofinish fasad

Universal material for puttying walls and ceilings is great for indoor and outdoor preparatory work. Well lays on any brick or concrete bases. The exception is the walls of gas silicate blocks and foam concrete - with them to use this putty is not recommended by the manufacturer. Cement base determines the maximum layer thickness - 2 mm, but after drying, the next can be applied, until the desired result is achieved.

Putty surfaces should be at a positive temperature, and after drying, the resulting layer has frost-resistant properties. Litokol Litofinish Fasad perfectly proved itself in severe climatic conditions. On average, the putty consumption is 1.4 kg / m² per 1 mm layer, which is quite economical compared to its closest competitors.

4 White house

White House universal putty based on acrylic copolymer, suitable for leveling exterior and interior walls. The thickness of the layer at the same time can reach up to 7 mm, which is an excellent indicator for the finished mixture. After applying the mixture after two hours completely freezes, reaching its full drying after a day. The resulting uniform coating has a white matte shade and is not taken at all.

White House putty is highly resistant to atmospheric conditions and frost. Given the moisture-resistant features of this mixture, it can be safely used for treating walls in rooms with high humidity, such as a basement, bath, kitchen, etc. It is also absolutely harmless to the environment, man, and completely odorless. The cost of this finishing material is fully justified by the quality and characteristics of the mixture, as well as durability, which provides resistance to external factors.

3 Unis Blick

The best option for budget finishes will be the use of Unis Blick putty. This composition is made on the basis of natural building materials. The manufacturer recommends using the mixture to seal small defects and cracks on various surfaces. Plastic mass can be used for installation of bathtubs, basins, toilet bowls, etc. The main field of application of putty is to decorate rooms with a favorable microclimate. The composition is not suitable for creating coatings in wet areas and on the facade of buildings. To apply a large putty layer, it is necessary to apply a reinforcing tape. When drying, the leveling layer does not shrink.

Masters finishers believe Unis Blik putty the best budget option for interior decoration. It is plastic, crack-resistant and quick-drying. But when drying, there may be flaking due to the presence of small stones in the composition.

2 VGT acrylic universal

It is very convenient for builders to create perfectly smooth surfaces using VGT universal putty. The acrylic-based product can be used to seal cracks in plaster, wood, concrete, brick, fiberboard and particleboard. Putty is recommended to use inside and outside buildings, only the base should be protected from direct exposure to precipitation. The thickness of one layer can vary in the range of 1-7 mm. After drying, a matte smooth coating is formed, with skillful use, the composition can act as a finishing treatment. Hard putty differs in small shrinkage and good adhesion to different materials.

Finishers like many qualities of VGT acrylic universal putty. It is convenient to apply and level, it has moisture resistance and frost resistance. The disadvantages of the material include the formation of fine, acrid dust when working, fast drying in a container with an unclosed lid.

1 KNAUF Fugen

Universal KNAUF Fugen putty is widely used. It is made on the basis of gypsum powder with the addition of polymeric additives. Additives increase the elasticity of the putty layer, improve adhesion. The main purpose of the mixture - alignment of walls and ceilings inside buildings, where there is a normal level of humidity. Since gypsum is hygroscopic, it is not recommended to putty bases in bathrooms and kitchens. As part of no toxic compounds, after drying, the coating does not crack due to the lack of shrinkage. With the help of putty, it is possible to level plastered and concrete surfaces, to seal joints in drywall constructions, and also to eliminate minor defects and cracks.

Professional builders are positive about the qualities of KNAUF Fugen putty, such as versatility, plasticity, good adhesion. But the solution quickly hardens and cannot be re-diluted with water.

Popular vote - who is the best producer of fillers?
We vote!

Will base

Volma

Bolars

Weber

Sheetrock

Miners

Knuf

VGT

Unis

Rusean

Bergauf

GLIMS

Ceresit

White house

Litokol

Total voted: 275

Vote results